A/c Ac Radiator Condenser Cooling Pusher Fan 5 Blade for 00-06 Bmw X5

  • Project Time: 3 hours
  • Tab: $200
  • Endowment
  • Tools: Arranged of sockets (8, 10, 13mm), trim board tool
  • Parts Required: Cooling fan
  • Performance Gain: Proper A/C function
  • Complementary Modification: Change cabin sink in

The engine-cooling rooter helps to keep off a constant railway locomotive temperature.

Information technology draws air past the radiator cooling fans, which in turn cools the engine coolant. An electric fan is mounted on the front of the radiator. The fan final stage is mounted to the fan and is controlled by the DME (engine control module). An additional belt-driven cooling fan with a viscous clutch is committed to the engine coolant pump. On this fan, the fluid in the viscous batch is affected by locomotive compartment temperature, which successively controls lover speed.

When replacing the railway locomotive side-cooling fan you will want to work with the engine icy and disconnect the battery negative cable television service. Disconnecting the negative battery cable will forestall the electric chilling fan from starting spell organism serviced. The lover could bulge out at any time and personal injury can occur. Assume't bound off this step.

The adjunct or a/c condenser fan in adorned to the front of the radiator. The secondary fan for this vehicle is dominated by the ECM and does not use relay race. The auxiliary fan request comes from the IHKA control mental faculty via the K-Bus. The fan stop number request is supported the refrigerating pressure sensor stimulus to the IHKA. Additional factors monitored by the ECM that influence fan operation are: Radiator outlet temperature sensor (exceeds the preset temperature), Vehicle speed, Battery voltage level. The auxiliary fan motor incorporates an output final phase that activates the lover motor at variable speeds. The output stage receives an output signal bespeak (pulse breadth modulated 10-100Hz) from the Electronic countermeasures, which activates the centrifugal.

Practical in the tree trunk, disconnect the battery negative transmission line and cover the battery terminal so that the cable length does not unexpectedly arrive in contact with the garbled telegraph. See our tech article connected battery replacing for notes on disconnecting and reconnecting the battery.

Hot tip

Forg with a cool engine

//

Project Photos

Placeholder Alt Text

Soma 1 The auxiliary or a/c condenser winnow in affixed to the front of the radiator (red arrow). The abundant support has to be removed to access it (green arrow).

Placeholder Alt Text

Work out 2 Prototypical we have to remove the uptake air passage that runs from the throttle housing (yellow arrow) to the mass air flow sensor (green pointer).

Placeholder Alt Text

Visualise 3 Working at the rested air intake, remove 4 plastic rivets (green arrows). Use a partner off of pliers (insert) to take out the center focus. One time all center rivets take in been abstracted, pull the duct up to detach it from the vehicle.

Placeholder Alt Text

Compute 4 Then lift the duct au fait the left-wing side while detaching it from the duct (green arrow) on the right wing side.

Placeholder Alt Text

Frame 5 Working at the exact broadside of the cooling fan shroud on the engine compartment, rip the electrical connector out of the mount (green arrow). And then disconnect the auxiliary winnow electric connector (red arrow) by squeezing the tabs and pulling the connecter apart.

Placeholder Alt Text

Figure 6 Working on the side of the cooling fan at the shroud, remove the plastic rivets (blood-red arrows). Pull the center pin forbidden and remove the rivet physical structure (inset).

Placeholder Alt Text

Figure 7 Functioning on the left-handed side of the bumper support below the headlamp, polish of the 2 10mm fasteners (red arrows). Recapitulate this step for the right side.

Placeholder Alt Text

Form 8 Working on the liberal side of the abundant support incoming to the cooling winnow, remove the three 10mm fasteners (special K arrows). Then remove the two 13mm fasteners (red arrows). Repeat this maltreat for the right side of meat.

Placeholder Alt Text

Figure 9 Workings below the advance wheel at the bracken-cooling duct (red arrow), remove the two 8mm brake canal fasteners (green arrows). Swinging the brake duct down and impossible of the way. Repeat this step for the true pull.

Placeholder Alt Text

Cipher 10 Working along the left side of the bumper support close to the Pteridium aquilinu duct intake, remove the two 13mm fasteners (red arrows). Support the bar (super acid pointer) when removing the final holdfast. Repeat this step for the far incline. Pull the bumper underpin away from the vehicle. Disconnect the horn connectors and parking distance sensors if equipped. Detach the wiring from the support and lay it apart.

Placeholder Alt Text

Figure 11 Working on the sides of the cooling fan, murder the ii 10mm fasteners (red arrows).

Placeholder Alt Text

Figure 12 Slide the cooling fan Down out of the radiator support (chromatic arrow) just enough to access the wiring.

Placeholder Alt Text

Figure 13 Detach the wiring from the radiator and feed it through the support (red pointer). Remove the lover from the fomite. With the cooling fan removed, clean any dust from the cooling fans and the radiator support.

Placeholder Alt Text

Figure 14 To install a new rooter, setback the steps of the procedure. Be sure to align the upper climb tabs (red pointer) with the slot on the vehicle (green arrow). Also route the wiring as it previously was routed.

Got more questions? Ask some of our automotive experts.

A/c Ac Radiator Condenser Cooling Pusher Fan 5 Blade for 00-06 Bmw X5

Source: https://www.pelicanparts.com/techarticles/BMW-X5/127-WATER-Auxiliary_Cooling_Fan_Replacement/127-WATER-Auxiliary_Cooling_Fan_Replacement.htm

Post a Comment

0 Comments